View LTM4613_4563839.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ltm4601hv 1 4601hvfb 12a 28v in dc/dc module regulator with pll, output tracking and margining n telecom and networking equipment n servers n industrial equipment n point of load regulation n complete switch mode power supply n wide input voltage range: 4.5v to 28v n 12a dc typical, 14a peak output current n 0.6v to 5v output voltage n output voltage tracking and margining n parallel multiple module ? regulators for current sharing n differential remote sensing for precision regulation n pll frequency synchronization n 1.5% regulation n current foldback protection (disabled at start-up) n rohs compliant with pb-free finish, gold finish lga (e4) or sac 305 bga (e1) n ultrafast transient response n current mode control n up to 95% efficiency at 5v in , 3.3v out n programmable soft-start n output overvoltage protection n small footprint, low profile (15mm 15mm 2.82mm) surface mount lga and (15mm 15mm 3.42mm) bga packages 2.5v/12a power supply with 4.5v to 28v input efficiency and power loss vs load current the ltm ? 4601hv is a complete 12a step-down switch mode dc/dc power supply with onboard switching control - ler, mosfets, inductor and all support components. the module regulator is housed in small surface mount 15mm 15mm 2.82mm lga and 15mm 15mm 3.42mm bga packages. operating over an input voltage range of 4.5v to 28v, the ltm4601hv supports an output voltage range of 0.6v to 5v as well as output voltage tracking and margining. the high efficiency design delivers 12a continuous current (14a peak). only bulk input and output capacitors are needed to complete the design. the low profile and light weight package easily mounts in unused space on the back side of pc boards for high density point of load regulation. the module regulator can be synchronized with an external clock for reducing undesirable frequency harmonics and allows polyphase ? operation for high load currents. a high switching frequency and adaptive on-time current mode architecture deliver a very fast transient response to line and load changes without sacrificing stability. an onboard differential remote sense amplifier can be used to accurately regulate an output voltage independent of load current. l , lt, ltc, ltm, linear technology, the linear logo, module and polyphase are registered trademarks and ltpowercad is a trademark of linear technology corporation. all other trademarks are the property of their respective owners. protected by u.s. patents including 5481178, 5847554, 6580258, 6304066, 6476589, 6774611, 6677210. typical application features description applications v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood run comp intv cc drv cc mpgm track/ss pllin ltm4601hv on/off r1 392k r set 19.1k margin control c out 4601hv ta01a v out 2.5v 12a clock sync track/ss control 100pf c in v in f set pgnd sgnd 5% margin v in 4.5v to 28v load current (a) 0 45 efficiency (%) power loss (w) 50 60 65 70 95 12v in 12v in 24v in 24v in 80 4 8 10 4601hv ta01b 55 85 90 75 0 1 6 3 4 5 2 2 6 12 14 power loss efficiency
ltm4601hv 2 4601hvfb intv cc , drv cc , v out_lcl , v out (v out 3.3v with remote sense amp) .................................... C0.3v to 6v pllin, track/ss, mpgm, marg0, marg1, pgood, f set .............................. C0.3v to intv cc + 0.3v run ............................................................. C0.3v to 5v v fb , comp ................................................ C0.3v to 2.7v (note 1) lead free finish tray part marking* package description temperature range ltm4601hvev#pbf ltm4601hvev#pbf ltm4601hvv 118-lead (15mm 15mm 2.82mm) lga C40c to 85c ltm4601hviv#pbf ltm4601hviv#pbf ltm4601hvv 118-lead (15mm 15mm 2.82mm) lga C40c to 85c ltm4601hvey#pbf ltm4601hvey#pbf ltm4601hvy 118-lead (15mm 15mm 3.42mm) bga C40c to 85c ltm4601hviy#pbf ltm4601hviy#pbf ltm4601hvy 118-lead (15mm 15mm 3.42mm) bga C40c to 85c consult ltc marketing for parts specified with wider operating temperature ranges. *the temperature grade is identified by a label on the shipping container. for more information on lead free part marking, go to: http://www.linear.com/leadfree/ this product is only offered in trays. for more information go to: http://www.linear.com/packaging/ absolute maximum ratings order information v in ............................................................. C0.3v to 28v v osns + , v osns C .......................... C0.3v to intv cc + 0.3v operating temperature range (note 2) .... C40c to 85c junction temperature ........................................... 125c storage temperature range .................. C55c to 125c marg1 drv cc v fb pgood sgnd v osns + diffv out v out_lcl v osns ? v in pgnd v out f set marg0 run comp mpgm pllin intv cc track/ss lga package 118-lead (15mm 15mm 2.82mm) top view t jmax = 125c, ja = 15c/w, jc = 6c/w, ja derived from 95mm 76mm pcb with 4 layers weight = 1.7g marg1 drv cc v fb pgood sgnd v osns + diffv out v out_lcl v osns ? v in pgnd v out f set marg0 run comp mpgm pllin intv cc track/ss bga package 118-lead (15mm 15mm 3.42mm) top view t jmax = 125c, ja = 15.5c/w, jc = 6.5c/w, ja derived from 95mm 76mm pcb with 4 layers weight = 1.9g pin configuration
ltm4601hv 3 4601hvfb symbol parameter conditions min typ max units v in(dc) input dc voltage l 4.5 28 v v out(dc) output voltage (with remote sense amp) c in = 10f 3, c out = 200f, r set = 40.2k v in = 12v, v out = 1.5v, i out = 0 l 1.478 1.5 1.522 v input specifications v in(uvlo) undervoltage lockout threshold i out = 0a 3.2 4 v i inrush(vin) input inrush current at startup i out = 0a. v out = 1.5v v in = 5v v in = 12v 0.6 0.7 a a i q(vin,no load) input supply bias current v in = 12v, no switching v in = 12v, v out = 1.5v, switching continuous v in = 5v, no switching v in = 5v, v out = 1.5v, switching continuous shutdown, run = 0, vin = 12v 3.8 38 2.5 42 22 ma ma ma ma a i s(vin) input supply current v in = 12v, v out = 1.5v, i out = 12a v in = 12v, v out = 3.3v, i out = 12a v in = 5v, v out = 1.5v, i out = 12a 1.81 3.63 4.29 a a a intv cc v in = 12v, run > 2v no load 4.7 5 5.3 v output specifications i outdc output continuous current range v in = 12v, v out = 1.5v (note 5) 0 12 a v out(line) v out line regulation accuracy v out = 1.5v, i out = 0a, v in from 4.5v to 28v l 0.3 % v out(load) v out load regulation accuracy v out = 1.5v, i out = 0a to 12a, with rsa (note 5) v in = 5v v in = 12v l l 0.25 0.25 % % v out(ac) output ripple voltage i out = 0a, c out = 2 100f x5r ceramic v in = 12v, v out = 1.5v v in = 5v, v out = 1.5v 20 18 mv p-p mv p-p f s output ripple voltage frequency i out = 5a, v in = 12v, v out = 1.5v 850 khz v out(start) turn-on overshoot c out = 200f, v out = 1.5v, i out = 0a, track/ss = 10nf v in = 12v v in = 5v 20 20 mv mv t start turn-on time c out = 200f, v out = 1.5v, track/ss = open, i out = 1a resistive load v in = 12v v in = 5v 0.5 0.5 ms ms v outls peak deviation for dynamic load load: 0% to 50% to 0% of full load, c out = 2 22f ceramic, 470f 4v sanyo poscap v in = 12v v in = 5v 35 35 mv mv t settle settling time for dynamic load step load: 0% to 50%, or 50% to 0% of full load v in = 12v 25 s i outpk output current limit c out = 200f ceramic v in = 12v, v out = 1.5v v in = 5v, v out = 1.5v 17 17 a a the l denotes the specifications which apply over the C40c to 85c temperature range (note 2), otherwise specifications are at t a = 25c, v in = 12v, per typical application (front page) configuration, r set = 40.2k. electrical characteristics
ltm4601hv 4 4601hvfb symbol parameter conditions min typ max units remote sense amp (note 3) v osns + , v osns C cm range common mode input voltage range v in = 12v, run > 2v 0 intv cc C 1 v diffv out range output voltage range v in = 12v, diffv out load = 100k 0 intv cc C 1 v v os input offset voltage magnitude 1.25 mv a v differential gain 1 v/v gbp gain bandwidth product 3 mhz sr slew rate 2 v/s r in input resistance v osns + to gnd 20 kw cmrr common mode rejection mode 100 db control stage v fb error amplifier input voltage accuracy i out = 0a, v out = 1.5v l 0.594 0.6 0.606 v v run run pin on/off threshold 1 1.5 1.9 v i track/ss soft-start charging current v track/ss = 0v C1.0 C1.5 C2.0 a t on(min) minimum on time (note 4) 50 100 ns t off(min) minimum off time (note 4) 250 400 ns r pllin pllin input resistance 50 k w i drvcc current into drv cc pin v out = 1.5v, i out = 1a, drv cc = 5v 18 25 ma r fbhi resistor between v out_lcl and v fb 60.098 60.4 60.702 k w v mpgm margin reference voltage 1.18 v v marg0 , v marg1 marg0, marg1 voltage thresholds 1.4 v pgood output v fbh pgood upper threshold v fb rising 7 10 13 % v fbl pgood lower threshold v fb falling C7 C10 C13 % v fb(hys) pgood hysteresis v fb returning 1.5 % the l denotes the specifications which apply over the C40c to 85c temperature range (note 2), otherwise specifications are at t a = 25c, v in = 12v, per typical application (front page) configuration, r set = 40.2k. note 1: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. exposure to any absolute maximum rating condition for extended periods may affect device reliability and lifetime. note 2: the ltm4601hv is tested under pulsed load conditions such that t j t a . the ltm4601hve is guaranteed to meet performance specifications from 0c to 85c. specifications over the C40c to 85c operating temperature range are assured by design, characterization and correlation with statistical process controls. the ltm4601hvi is guaranteed over the C40c to 85c temperature range. note 3: remote sense amplifier recommended for 3.3v output. note 4: 100% tested at wafer level only. note 5: see output current derating curves for different v in , v out and t a . electrical characteristics
ltm4601hv 5 4601hvfb efficiency vs load current with 5v in efficiency vs load current with 12v in efficiency vs load current with 24v in 1.2v transient response 1.5v transient response 2.5v transient response 3.3v transient response (see figures 19 and 20 for all curves) 1.8v transient response typical performance characteristics load current (a) 0 efficiency (%) 75 80 85 15 4601hv g01 70 65 60 5 10 90 95 100 0.6v out 1.2v out 1.5v out 2.5v out 3.3v out load current (a) 0 50 efficiency (%) 55 65 70 75 100 85 5 10 4601hv g02 60 90 95 80 15 0.6v out 1.2v out 1.5v out 2.5v out 3.3v out 5v out load current (a) 0 45 efficiency (%) 55 60 65 70 75 80 5 10 4601hv g03 85 90 95 50 15 1.5v out 2.5v out 3.3v out 5.0v out v out 50mv/div 20s/div 4601hv g04 0a to 6a load step 1.2v at 6a/s load step c out = 3 ? 22f 6.3v ceramics 470f 4v sanyo poscap c3 = 100pf v out 50mv/div 20s/div 4601hv g05 0a to 6a load step 1.5v at 6a/s load step c out = 3 ? 22f 6.3v ceramics 470f 4v sanyo poscap c3 = 100pf v out 50mv/div 20s/div 4601hv g06 0a to 6a load step 1.8v at 6a/s load step c out = 3 ? 22f 6.3v ceramics 470f 4v sanyo poscap c3 = 100pf v out 50mv/div 20s/div 4601hv g07 0a to 6a load step 2.5v at 6a/s load step c out = 3 ? 22f 6.3v ceramics 470f 4v sanyo poscap c3 = 100pf v out 50mv/div 20s/div 4601 g08 0a to 6a load step 3.3v at 6a/s load step c out = 3 ? 22f 6.3v ceramics 470f 4v sanyo poscap c3 = 100pf
ltm4601hv 6 4601hvfb (see figures 19 and 20 for all curves) start-up, i out = 12a (resistive load) start-up, i out = 0a v in to v out step-down ratio short-circuit protection, i out = 0a short-circuit protection, i out = 12a track, i out = 12a typical performance characteristics v out 0.5v/div 5ms/div 4601hv g09 i in 0.5a/div v in = 12v v out = 1.5v c out = 470f, 3 22f soft-start = 10nf v out 0.5v/div 2ms/div 4601hv g10 i in 1a/div v in = 12v v out = 1.5v c out = 470f, 3 22f soft-start = 10nf input voltage (v) 0 output voltage (v) 3.0 4.0 5.5 5.0 16 4601hv g11 2.0 1.0 2.5 3.5 4.5 1.5 0.5 0 42 86 12 14 18 10 20 22 24 3.3v output with 130k from v out to i on 5v output with 100k resistor added from f set to gnd 5v output with no resistor added from f set to gnd 2.5v output 1.8v output 1.5v output 1.2v output v fb 0.5v/div track/ss 0.5v/div 2ms/div 4601hv g12 v out 1v/div v in = 12v v out = 1.5v c out = 470f, 3 22f soft-start = 10nf v out 0.5v/div 50s/div 4601hv g13 i in 1a/div v in = 12v v out = 1.5v c out = 470f, 3 22f soft-start = 10nf v out 0.5v/div 50s/div 4601hv g14 i in 1a/div v in = 12v v out = 1.5v c out = 470f, 3 22f soft-start = 10nf
ltm4601hv 7 4601hvfb (see package description for pin assignment) v in (bank 1): power input pins. apply input voltage be - tween these pins and pgnd pins. recommend placing input decoupling capacitance directly between v in pins and pgnd pins. v out (bank 3): power output pins. apply output load between these pins and pgnd pins. recommend placing output decoupling capacitance directly between these pins and pgnd pins. see figure 17. pgnd (bank 2): power ground pins for both input and output returns. v osns C (pin m12): (C) input to the remote sense ampli - fier. this pin connects to the ground remote sense point. the remote sense amplifier is used for v out 3.3v. tie to intv cc if not used. v osns + (pin j12): (+) input to the remote sense ampli - fier. this pin connects to the output remote sense point. the remote sense amplifier is used for v out 3.3v. tie to ground if not used. diffv out (pin k12): output of the remote sense ampli - fier. this pin connects to the v out_lcl pin. leave floating if remote sense amplifier is not used. drv cc (pin e12): this pin normally connects to intv cc for powering the internal mosfet drivers. this pin can be biased up to 6v from an external supply with about 50ma capability, or an external circuit as shown in figure 18. this improves efficiency at the higher input voltages by reducing power dissipation in the module. intv cc (pin a7): this pin is for additional decoupling of the 5v internal regulator. pllin (pin a8): external clock synchronization input to the phase detector. this pin is internally terminated to sgnd with a 50k resistor. apply a clock with a high level above 2v and below intv cc . see the applications information section. track/ss (pin a9): output voltage tracking and soft- start pin. when the module is configured as a master output, then a soft-start capacitor is placed on this pin to ground to control the master ramp rate. a soft-start capacitor can be used for soft-start turn on of a stand alone regulator. slave operation is performed by putting a resistor divider from the master output to ground, and connecting the center point of the divider to this pin. see the applications information section. mpgm (pin a12): programmable margining input. a re - sistor from this pin to ground sets a current that is equal to 1.18v/r. this current multiplied by 10k w will equal a value in millivolts that is a percentage of the 0.6v refer - ence voltage. see applications information. to parallel ltm4601hvs, each requires an individual mpgm resistor. do not tie mpgm pins together. f set (pin b12): frequency set internally to 850khz. an external resistor can be placed from this pin to ground to increase frequency. see the applications information section for frequency adjustment. v fb (pin f12): the negative input of the error amplifier. internally, this pin is connected to v out_lcl pin with a 60.4k precision resistor. different output voltages can be programmed with an additional resistor between v fb and sgnd pins. see the applications information section. marg0 (pin c12): this pin is the lsb logic input for the margining function. together with the marg1 pin it will determine if margin high, margin low or no margin state is applied. the pin has an internal pull-down resistor of 50k. see the applications information section. marg1 (pin d12): this pin is the msb logic input for the margining function. together with the marg0 pin it will determine if margin high, margin low or no margin state is applied. the pin has an internal pull-down resistor of 50k. see the applications information section. pin functions
ltm4601hv 8 4601hvfb (see package description for pin assignment) pin functions sgnd (pin h12): signal ground. this pin connects to pgnd at output capacitor point. see figure 17. comp (pin a11): current control threshold and error amplifier compensation point. the current comparator threshold increases with this control voltage. the voltage ranges from 0v to 2.4v with 0.7v corresponding to zero sense voltage (zero current). pgood (pin g12): output voltage power good indicator. open-drain logic output that is pulled to ground when the output voltage is not within 10% of the regulation point, after a 25s power bad mask timer expires. run (pin a10): run control pin. a voltage above 1.9v will turn on the module, and when below 1v, will turn off the module. a programmable uvlo function can be accomplished by connecting to a resistor divider from v in to ground. see figure 1. this pin has a 5.1v zener to ground. maximum pin voltage is 5v. limit current into the run pin to less than 1ma. v out_lcl (pin l12): v out connects directly to this pin to bypass the remote sense amplifier, or diffv out connects to this pin when remote sense amplifier is used.
ltm4601hv 9 4601hvfb figure 1. simplified ltm4601hv block diagram symbol parameter conditions min typ max units c in external input capacitor requirement (v in = 4.5v to 28v, v out = 2.5v) i out = 12a, 3 10f ceramics 20 30 f c out external output capacitor requirement (v in = 4.5v to 28v, v out = 2.5v) i out = 12a 100 200 f t a = 25c, v in = 12v. use figure 1 configuration. decoupling requirements simplified block diagram + internal comp sgnd comp pgood run uvlo function v out_lcl v in >1.9v = on <1v = off max = 5v marg1 marg0 mpgm pllin c ss intv cc drv cc track/ss v fb f set 50k 39.2k r set 19.1k 50k 60.4k v out 1m 5.1v zener power control q1 v in 4.5v to 28v v out 2.5v 12a q2 10k 0.47h 10k 10k 50k 10k intv cc 2.2 + ? 22f 1.5f c in + c out pgnd v osns ? v osns + diffv out 4601hv f01 4.7f r1 r2 = sgnd = pgnd
ltm4601hv 10 4601hvfb power module description the ltm4601hv is a standalone nonisolated switching mode dc/dc power supply. it can deliver up to 12a of dc output current with some external input and output capacitors. this module provides a precisely regulated output voltage programmable via one external resistor from 0.6v dc to 5.0v dc over a 4.5v to 28v wide input voltage. the typical application schematics are shown in figures 19 and 20. the ltm4601hv has an integrated constant on-time current mode regulator, ultralow r ds(on) fets with fast switching speed and integrated schottky diodes. the typical switching frequency is 850khz at full load. with current mode control and internal feedback loop compensation, the ltm4601hv module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors, even all ceramic output capacitors. current mode control provides cycle-by-cycle fast current limit. besides, foldback current limiting is provided in an overcurrent condition while v fb drops. internal overvolt - age and undervoltage comparators pull the open-drain pgood output low if the output feedback voltage exits a 10% window around the regulation point. furthermore, in an overvoltage condition, internal top fet q1 is turned off and bottom fet q2 is turned on and held on until the overvoltage condition clears. pulling the run pin below 1v forces the controller into its shutdown state, turning off both q1 and q2. at low load current, the module works in continuous current mode by default to achieve minimum output voltage ripple. when drv cc pin is connected to intv cc an integrated 5v linear regulator powers the internal gate drivers. if a 5v external bias supply is applied on the drv cc pin, then an efficiency improvement will occur due to the reduced power loss in the internal linear regulator. this is especially true at the high end of the input voltage range. the ltm4601hv has a very accurate differential remote sense amplifier with very low offset. this provides for very accurate output voltage sensing at the load. the mpgm pin, marg0 pin and marg1 pin are used to support voltage margining, where the percentage of margin is programmed by the mpgm pin, and marg0 and marg1 select margining. the pllin pin provides frequency synchronization of the device to an external clock. the track/ss pin is used for power supply tracking and soft-start programming. operation
ltm4601hv 11 4601hvfb the typical ltm4601hv application circuits are shown in figures 19 and 20. external component selection is primar - ily determined by the maximum load current and output voltage. refer to table 2 for specific external capacitor requirements for a particular application. v in to v out step-down ratios there are restrictions in the maximum v in to v out step down ratio that can be achieved for a given input voltage. these constraints are shown in the typical performance characteristics curves labeled v in to v out step-down ratio. note that additional thermal derating may apply. see the thermal considerations and output current derating section of this data sheet. output voltage programming and margining the pwm controller has an internal 0.6v reference voltage. as shown in the block diagram, a 1m and a 60.4k 0.5% internal feedback resistor connects v out and v fb pins together. the v out_lcl pin is connected between the 1m and the 60.4k resistor. the 1m resistor is used to protect against an output overvoltage condition if the v out_lcl pin is not connected to the output, or if the remote sense amplifier output is not connected to v out_lcl . in these cases, the output voltage will default to 0.6v. adding a resistor r set from the v fb pin to sgnd pin programs the output voltage: v out = 0.6v 60.4k + r set r set or equivalently: r set = 60.4k v out 0.6v ? 1 ? ? ? ? ? ? table 1. r set standard 1% resistor values vs v out r set (k w ) open 60.4 40.2 30.1 25.5 19.1 13.3 8.25 v out (v) 0.6 1.2 1.5 1.8 2 2.5 3.3 5 the mpgm pin programs a current that when multiplied by an internal 10k resistor sets up the 0.6v reference offset for margining. a 1.18v reference divided by the rpgm resistor on the mpgm pin programs the current. calculate v out(margin) : v out(margin) = %v out 100 ? v out where %v out is the percentage of v out you want to margin, and v out(margin) is the margin quantity in volts: r pgm = v out 0.6v ? 1.18v v out(margin) ? 10k where r pgm is the resistor value to place on the mpgm pin to ground. the margining voltage, v out(margin) , will be added or subtracted from the nominal output voltage as determined by the state of the marg0 and marg1 pins. see the truth table below: marg1 marg0 mode low low no margin low high margin up high low margin down high high no margin input capacitors ltm4601hv module should be connected to a low ac impedance dc source. input capacitors are required to be placed adjacent to the module. in figure 20, the 10f ceramic input capacitors are selected for their ability to handle the large rms current into the converter. an input bulk capacitor of 100f is optional. this 100f capacitor is only needed if the input source impedance is compro - mised by long inductive leads or traces. for a buck converter, the switching duty-cycle can be estimated as: d = v out v in applications information
ltm4601hv 12 4601hvfb without considering the inductor ripple current, the rms current of the input capacitor can be estimated as: i cin(rms) = i out(max) % ? d ? 1Cd ( ) in the above equation, % is the estimated efficiency of the power module. c in can be a switcher-rated electrolytic aluminum capacitor, os-con capacitor or high value ce - ramic capacitor. note the capacitor ripple current ratings are often based on temperature and hours of life. this makes it advisable to properly derate the input capacitor, or choose a capacitor rated at a higher temperature than required. always contact the capacitor manufacturer for derating requirements. in figures 19 and 20, the 10f ceramic capacitors are to - gether used as a high frequency input decoupling capacitor. in a typical 12a output application, three very low esr, x5r or x7r, 10f ceramic capacitors are recommended. these decoupling capacitors should be placed directly adjacent to the module input pins in the pcb layout to minimize the trace inductance and high frequency ac noise. each 10f ceramic is typically good for 2a to 3a of rms ripple current. refer to your ceramics capacitor catalog for the rms current ratings. multiphase operation with multiple ltm4601hv devices in parallel will lower the effective input rms ripple current due to the interleaving operation of the regulators. application note 77 provides a detailed explanation. refer to figure 2 for the input capacitor ripple current reduction as a func - tion of the number of phases. the figure provides a ratio of rms ripple current to dc load current as function of duty cycle and the number of paralleled phases. pick the corresponding duty cycle and the number of phases to arrive at the correct ripple current value. for example, the 2-phase parallel ltm4601hv design provides 24a at 2.5v output from a 12v input. the duty cycle is dc = 2.5v/12v = 0.21. the 2-phase curve has a ratio of ~0.25 for a duty cycle of 0.21. this 0.25 ratio of rms ripple current to a dc load current of 24a equals ~6a of input rms ripple current for the external input capacitors. output capacitors the ltm4601hv is designed for low output ripple voltage. the bulk output capacitors defined as c out are chosen with low enough effective series resistance (esr) to meet the output voltage ripple and transient requirements. c out can be a low esr tantalum capacitor, a low esr polymer capacitor or a ceramic capacitor. the typical capacitance is 200f if all ceramic output capacitors are used. additional output filtering may be required by the system designer if further reduction of output ripple or dynamic transient spike is required. table 2 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 5a/s transient. the table optimizes total equivalent esr and total bulk capacitance to maximize transient performance. figure 2. normalized input rms ripple current vs duty cycle for one to six modules (phases) applications information duty cycle (v out /v in ) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.6 0.5 0.4 0.3 0.2 0.1 0 4601hv f02 rms input ripple current dc load current 6-phase 4-phase 12-phase 3-phase 2-phase 1-phase
ltm4601hv 13 4601hvfb multiphase operation with multiple ltm4601hv devices in parallel will lower the effective output ripple current due to the interleaving operation of the regulators. for example, each ltm4601hvs inductor current in a 12v to 2.5v multiphase design can be read from the inductor ripple current vs duty cycle graph (figure 3). the large ripple current at low duty cycle and high output voltage can be reduced by adding an external resistor from f set to ground which increases the frequency. if the duty cycle is dc = 2.5v/12v = 0.21, the inductor ripple current for 2.5v output at 21% duty cycle is ~6a in figure 3. figure 4 provides a ratio of peak-to-peak output ripple cur - rent to the inductor current as a function of duty cycle and the number of paralleled phases. pick the corresponding duty cycle and the number of phases to arrive at the correct output ripple current ratio value. if a 2-phase operation is chosen at a duty cycle of 21%, then 0.6 is the ratio. this 0.6 ratio of output ripple current to inductor ripple of 6a equals 3.6a of effective output ripple current. refer to application note 77 for a detailed explanation of output ripple current reduction as a function of paralleled phases. the output ripple voltage has two components that are related to the amount of bulk capacitance and effective series resistance (esr) of the output bulk capacitance. figure 4. normalized output ripple current vs duty cycle, dlr = v o t/l i , dlr = each phases inductor current figure 3. inductor ripple current vs duty cycle applications information duty cycle (v out /v in ) 0 0 i l (a) 2 4 6 8 10 12 0.2 0.4 0.6 0.8 4601hv f03 2.5v output 5v output 1.8v output 1.5v output 1.2v output 3.3v output with 130k added from v out to f set 5v output with 100k added from f set to gnd duty cycle (v o /v in ) 0.1 0.15 0.2 0.25 0.350.3 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 4601hv f04 6-phase 4-phase 3-phase 2-phase 1-phase peak-to-peak output ripple current dir ratio =
ltm4601hv 14 4601hvfb therefore, the output ripple voltage can be calculated with the known effective output ripple current. the equation: v out(p-p) ( i l /(8 ? f ? m ? c out ) + esr ? i l ), where f is frequency and m is the number of parallel phases. this calculation process can be easily accomplished by using ltpowercad?. fault conditions: current limit and overcurrent foldback ltm4601hv has a current mode controller, which inher - ently limits the cycle-by-cycle inductor current not only in steady-state operation, but also in response to transients. to further limit current in the event of an overload condi - tion, the ltm4601hv provides foldback current limiting. if the output voltage falls by more than 50%, then the maximum output current is progressively lowered to about one sixth of its full current limit value. the current limit returns to its nominal value once v out and v fb have returned to their nominal values. soft-start and tracking the track/ss pin provides a means to either soft-start the regulator or track it to a different power supply. a capacitor on this pin will program the ramp rate of the output voltage. a 1.5a current source will charge up the external soft-start capacitor to 80% of the 0.6v internal voltage reference plus or minus any margin delta. this will control the ramp of the internal reference and the output voltage. the total soft-start time can be calculated as: t softstart = 0.8 ? 0.6v v out(margin) ( ) ? c ss 1.5a when the run pin falls below 1.5v, then the track/ss pin is reset to allow for proper soft-start control when the regulator is enabled again. current foldback and forced continuous mode are disabled during the soft-start pro - cess. the soft-start function can also be used to control the output ramp up time, so that another regulator can be easily tracked to it. output voltage tracking output voltage tracking can be programmed externally using the track/ss pin. the output can be tracked up and down with another regulator. the master regulators output is divided down with an external resistor divider that is the same as the slave regulators feedback divider. figure 5 shows an example of coincident tracking. ratiometric modes of tracking can be achieved by selecting different resistor values to change the output tracking ratio. the master output must be greater than the slave output for the tracking to work. figure 6 shows the coincident output tracking characteristics. figure 5. coincident tracking schematic figure 6. coincident output tracking characteristics applications information v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss track control pllin ltm4601hv r set 40.2k 100k r1 40.2k master output r2 60.4k c out slave output 4601hv f05 c in v in f set pgnd sgnd v in output voltage time 4601hv f06 master output slave output
ltm4601hv 15 4601hvfb run enable the run pin is used to enable the power module. the pin has an internal 5.1v zener to ground. the pin can be driven with a logic input not to exceed 5v. the run pin can also be used as an undervoltage lock out (uvlo) function by connecting a resistor divider from the input supply to the run pin: v uvlo = r1 + r2 r2 ? 1.5v see figure 1, simplified block diagram. power good the pgood pin is an open-drain pin that can be used to monitor valid output voltage regulation. this pin monitors a 10% window around the regulation point and tracks with margining. comp pin this pin is the external compensation pin. the module has already been internally compensated for most output voltages. table 2 is provided for most application require - ments. ltpowercad is available for other control loop optimization. pllin the power module has a phase-locked loop comprised of an internal voltage controlled oscillator and a phase detector. this allows the internal top mosfet turn-on to be locked to the rising edge of the external clock. the frequency range is 30% around the operating frequency of 850khz. a pulse detection circuit is used to detect a clock on the pllin pin to turn on the phase-locked loop. the pulse width of the clock has to be at least 400ns and at least 2v in amplitude. the pllin pin must be driven from a low impedance source such as a logic gate located close to the pin. during the start-up of the regulator, the phase-locked loop function is disabled. intv cc and drv cc connection an internal low dropout regulator produces an internal 5v supply that powers the control circuitry and drv cc for driving the internal power mosfets. therefore, if the system does not have a 5v power rail, the ltm4601hv can be directly powered by v in . the gate driver current through the ldo is about 20ma. the internal ldo power dissipation can be calculated as: p ldo_loss = 20ma ? (v in C 5v) the ltm4601hv also provides the external gate driver voltage pin drv cc . if there is a 5v rail in the system, it is recommended to connect drv cc pin to the external 5v rail. this is especially true for higher input voltages. do not apply more than 6v to the drv cc pin. a 5v output can be used to power the drv cc pin with an external circuit as shown in figure 18. parallel operation of the module the ltm4601hv device is an inherently current mode controlled device. parallel modules will have very good current sharing. this will balance the thermals on the design. the voltage feedback equation changes with the variable n as modules are paralleled: v out = 0.6v ? 60.4k n + r set r set or equivalently: r set = 60.4k n v out 0.6v ? 1 ? ? ? ? ? ? where n is the number of paralleled modules. figure 21 shows two ltm4601hv modules used in a par - allel design. an ltm4601hv device can be used without the remote sense amplifier. applications information
ltm4601hv 16 4601hvfb figure 7. 1.5v out power loss figure 9. no heat sink 5v in load current (a) 0 0 power loss (w) 1.0 2.0 3.0 2 4 6 8 4601hv f07 10 24v in 4.0 5.0 0.5 1.5 2.5 3.5 4.5 5v in 12 12v in figure 10. bga heat sink 5v in load current (a) 0 0 power loss (w) 1 2 3 4 6 2 4 6 8 4601hv f08 10 12 5 24v in 12v in ambient temperature (c) 50 0 maximum load current (a) 2 4 6 8 10 12 60 70 80 90 4601hv f09 100 5v in , 1.5v out 0lfm 5v in , 1.5v out 200lfm 5v in , 1.5v out 400lfm ambient temperature (c) 50 0 maximum load current (a) 2 4 6 8 10 12 60 70 80 90 4601hv f10 100 5v in , 1.5v out 0lfm 5v in , 1.5v out 200lfm 5v in , 1.5v out 400lfm figure 8. 3.3v out power loss applications information thermal considerations and output current derating the power loss curves in figures 7 and 8 can be used in coordination with the load current derating curves in figures 9 to 16 for calculating an approximate ja for the module with various heat sinking methods. thermal models are derived from several temperature measurements at the bench and thermal modeling analysis. thermal ap - plication note 103 provides a detailed explanation of the analysis for the thermal models and the derating curves. tables 3 and 4 provide a summary of the equivalent ja for the noted conditions. these equivalent ja parameters are correlated to the measured values, and are improved with air flow. the case temperature is maintained at 100c or below for the derating curves. the maximum case temperature of 100c is to allow for a rise of about 13c to 25c inside the module with a thermal resistance jc from junction to case between 6c/w to 9c/w. this will maintain the maximum junction temperature inside the module below 125c. safety considerations the ltm4601hv modules do not provide isolation from v in to v out . there is no internal fuse. if required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure.
ltm4601hv 17 4601hvfb figure 13. 12v in , 3.3v out , no heat sink ambient temperature (c) 40 0 maximum load current (a) 2 4 6 8 10 12 60 80 4601hv f13 100 0lfm 200lfm 400lfm figure 14. 12v in , 3.3v out , bga heat sink ambient temperature (c) 40 0 maximum load current (a) 2 4 6 8 10 12 60 80 4601hv f14 100 0lfm 200lfm 400lfm figure 15. 24v in , 1.5v out , no heat sink ambient temperature (c) 40 0 maximum load current (a) 2 4 6 8 10 12 60 80 4601hv f15 100 24v in , 1.5v out 0lfm 24v in , 1.5v out 200lfm 24v in , 1.5v out 400lfm ambient temperature (c) 40 0 maximum load current (a) 2 4 6 8 10 12 60 80 4601hv f16 100 24v in , 1.5v out 0lfm 24v in , 1.5v out 200lfm 24v in , 1.5v out 400lfm figure 16. 24v in , 1.5v out , bga heat sink applications information figure 11. no heat sink 12v in figure 12. bga heat sink 12v in ambient temperature (c) 50 0 maximum load current (a) 2 4 6 8 10 12 60 70 80 90 4601hv f12 100 12v in , 1.5v out 0lfm 12v in , 1.5v out 200lfm 12v in , 1.5v out 400lfm ambient temperature (c) 50 0 maximum load current (a) 2 4 6 8 10 12 60 70 80 90 4601hv f11 100 12v in , 1.5v out 0lfm 12v in , 1.5v out 200lfm 12v in , 1.5v out 400lfm
ltm4601hv 18 4601hvfb table 2. output voltage response versus component matrix* (refer to figures 19 and 20), 0a to 6a load step typical measured values c out1 vendors part number c out2 vendors part number tdk c4532x5r0j107mz (100f, 6.3v) sanyo poscap 6tpe330mil (330f, 6.3v) taiyo yuden jmk432bj107mu-t (100f, 6.3v) sanyo poscap 2r5tpe470m9 (470f, 2.5v) taiyo yuden jmk316bj226ml-t501 (22f, 6.3v) sanyo poscap 4tpe470mcl (470f, 4v) v out (v) c in (ceramic) c in (bulk) c out1 (ceramic) c out2 (bulk) c comp c3 v in (v) droop (mv) peak to peak (mv) recovery time (s) load step (a/s) r set (k w ) 1.2 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 47pf 5 70 140 30 6 60.4 1.2 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 100pf 5 35 70 20 6 60.4 1.2 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 22pf 5 70 140 20 6 60.4 1.2 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 5 40 93 30 6 60.4 1.2 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 100pf 12 70 140 30 6 60.4 1.2 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 100pf 12 35 70 20 6 60.4 1.2 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 22pf 12 70 140 20 6 60.4 1.2 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 12 49 98 20 6 60.4 1.5 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 100pf 5 48 100 35 6 40.2 1.5 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 33pf 5 54 109 30 6 40.2 1.5 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 5 44 84 30 6 40.2 1.5 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 5 61 118 30 6 40.2 1.5 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 100pf 12 48 100 35 6 40.2 1.5 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 33pf 12 54 109 30 6 40.2 1.5 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 12 44 89 25 6 40.2 1.5 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 12 54 108 25 6 40.2 1.8 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 47pf 5 48 100 30 6 30.1 1.8 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 100pf 5 44 90 20 6 30.1 1.8 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 5 68 140 30 6 30.1 1.8 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 5 65 130 30 6 30.1 1.8 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 100pf 12 60 120 30 6 30.1 1.8 2 10f 35v 150f 35v 1 100f 6.3v 470f 2.5v none 100pf 12 60 120 30 6 30.1 1.8 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 12 68 140 30 6 30.1 1.8 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 12 65 130 20 6 30.1 2.5 2 10f 35v 150f 35v 1 100f 6.3v 470f 4v none 100pf 5 48 103 30 6 19.1 2.5 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 220pf 5 56 113 30 6 19.1 2.5 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none none 5 57 116 30 6 19.1 2.5 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 5 60 115 25 6 19.1 2.5 2 10f 35v 150f 35v 1 100f 6.3v 470f 4v none 100pf 12 48 103 30 6 19.1 2.5 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none none 12 51 102 30 6 19.1 2.5 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 220pf 12 56 113 30 6 19.1 2.5 2 10f 35v 150f 35v 4 100f 6.3v none none 220pf 12 70 140 25 6 19.1 3.3 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 7 120 240 30 6 13.3 3.3 2 10f 35v 150f 35v 1 100f 6.3v 470f 4v none 100pf 7 110 214 30 6 13.3 3.3 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 100pf 7 110 214 30 6 13.3 3.3 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 7 114 230 30 6 13.3 3.3 2 10f 35v 150f 35v 1 100f 6.3v 470f 4v none 100pf 12 110 214 30 6 13.3 3.3 2 10f 35v 150f 35v 3 22f 6.3v 470f 4v none 150pf 12 110 214 35 6 13.3 3.3 2 10f 35v 150f 35v 2 100f 6.3v 330f 6.3v none 100pf 12 110 214 35 6 13.3 3.3 2 10f 35v 150f 35v 4 100f 6.3v none none 100pf 12 114 230 30 6 13.3 5 2 10f 35v 150f 35v 4 100f 6.3v none none 22pf 15 188 375 25 6 8.25 5 2 10f 35v 150f 35v 4 100f 6.3v none none 22pf 20 159 320 25 6 8.25 * x7r is recommended for extended temperature range. applications information
ltm4601hv 19 4601hvfb table 3. 1.5v output at 12a derating curve v in (v) power loss curve air flow (lfm) heat sink ja (c/w) lga ja (c/w) bga figures 9, 11, 15 5, 12, 24 figure 7 0 none 15.2 15.7 figures 9, 11, 15 5, 12, 24 figure 7 200 none 14 14.5 figures 9, 11, 15 5, 12, 24 figure 7 400 none 12 12.5 figures 10, 12, 16 5, 12, 24 figure 7 0 bga heat sink 13.9 14.4 figures 10, 12, 16 5, 12, 24 figure 7 200 bga heat sink 11.3 11.8 figures 10, 12, 16 5, 12, 24 figure 7 400 bga heat sink 10.25 10.75 table 4. 3.3v output at 12a derating curve v in (v) power loss curve air flow (lfm) heat sink ja (c/w) lga ja (c/w) bga figure 13 12 figure 8 0 none 15.2 15.7 figure 13 12 figure 8 200 none 14.6 15.0 figure 13 12 figure 8 400 none 13.4 13.9 figure 14 12 figure 8 0 bga heat sink 13.9 14.4 figure 14 12 figure 8 200 bga heat sink 11.1 11.6 figure 14 12 figure 8 400 bga heat sink 10.5 11.0 heat sink manufacturer aavid thermalloy part no: 375424b00034g phone: 603-224-9988 applications information
ltm4601hv 20 4601hvfb figure 17. recommended layout (lga and bga pcb layouts are identical with the exception of circle pads for bga. see package description.) applications information signal gnd v out v in gnd c out c in c in c out 4601hv f17 layout checklist/example the high integration of ltm4601hv makes the pcb board layout very simple and easy. however, to optimize its electri - cal and thermal performance, some layout considerations are still necessary. ? use large pcb copper areas for high current path, in - cluding v in , pgnd and v out . it helps to minimize the pcb conduction loss and thermal stress. ? place high frequency ceramic input and output capaci - tors next to the v in , pgnd and v out pins to minimize high frequency noise. ? place a dedicated power ground layer underneath the unit. refer frequency synchronization source to power ground. ? to minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. ? do not put vias directly on pads unless they are capped. ? use a separated sgnd copper area for components connected to signal pins. connect the sgnd to pgnd underneath the unit. figure 17 gives a good example of the recommended layout. frequency adjustment the ltm4601hv is designed to typically operate at 850khz across most input conditions. the f set pin is normally left open. the switching frequency has been optimized for maintaining constant output ripple noise over most operating ranges. the 850khz switching frequency and the 400ns minimum off time can limit operation at higher duty cycles like 5v to 3.3v, and produce excessive induc - tor ripple currents for lower duty cycle applications like 28v to 5v. the 5v out and 3.3v out drop out curves are modified by adding an external resistor on the f set pin to allow for lower input voltage operation, or higher input voltage operation. example for 5v output ltm4601hv minimum on-time = 100ns t on = ((v out ? 10pf)/i fset ), for v out > 4.8v use 4.8v ltm4601hv minimum off-time = 400ns t off = t C t on , where t = 1/frequency duty cycle = t on /t or v out /v in equations for setting frequency: i fset = (v in /(3 ? r fset )), for 28v operation, i fset = 238a, t on = ((4.8 ? 10pf)/i fset ), t on = 202ns, where the internal r fset is 39.2k. frequency = (v out /(v in ? t on )) = (5v/(28 ? 202ns)) ~ 884khz. the inductor ripple current begins to get high at the higher input voltages due to a larger voltage across the inductor. this is noted in the typical inductor ripple current vs duty cycle graph (figure 3) where i l 10a at 20% duty cycle. the inductor ripple current can be lowered at the higher input voltages by adding an external resistor from f set to ground to increase the switching frequency. a 7a ripple current is chosen, and the total peak current is equal to 1/2 of the 7a ripple current plus the output current. the 5v output current is limited to 8a, so the total peak current is less than 11.5a. this is below the 14a peak specified value. a 100k resistor is placed from f set to ground, and the parallel combination of 100k and 39.2k equates to 28k. the i fset calculation with 28k and 28v input voltage equals 333a. this equates to a t on of 144ns. this will increase the switching frequency from ~884khz to ~1.24mhz for the 28v to 5v conversion.
ltm4601hv 21 4601hvfb the minimum on-time is above 100ns at 28v input. since the switching frequency is approximately constant over input and output conditions, then the lower input voltage range is limited to 10v for the 1.24mhz operation due to the 400ns minimum off-time. equation: t on = (v out /v in ) ? (1/frequency) equates to a 400ns on-time, and a 400ns off-time. the v in to v out step-down ratio curve reflects an operating range of 10v to 28v for 1.24mhz operation with a 100k resistor to ground as shown in figure 18, and an 8v to 16v operation for f set floating. these modifica- tions are made to provide wider input voltage ranges for the 5v output designs while limiting the inductor ripple current, and maintaining the 400ns minimum off-time. example for 3.3v output ltm4601hv minimum on-time = 100ns t on = ((v out ? 10pf)/i fset ) ltm4601hv minimum off-time = 400ns t off = t C t on , where t = 1/frequency duty cycle (dc) = t on /t or v out /v in equations for setting frequency: i fset = (v in /(3 ? r fset )), for 28v operation, i fset = 238a, t on = ((3.3 ? 10pf)/i fset ), t on = 138.7ns, where the internal r fset is 39.2k. frequency = (v out /(v in ? t on )) = (3.3v/(28 ? 138.7ns)) ~ 850khz. the minimum on-time and minimum off-time are within specification at 139ns and 1037ns. the 4.5v minimum input for converting 3.3v output will not meet the minimum off-time specification of 400ns. t on = 868ns, frequency = 850khz, t off = 315ns. solution lower the switching frequency at lower input voltages to allow for higher duty cycles, and meet the 400ns minimum off-time at 4.5v input voltage. the off-time should be about 500ns, which includes a 100ns guard band. the duty cycle for (3.3v/4.5v) = ~73%. frequency = (1 C dc)/t off or (1 C 0.73)/500ns = 540khz. the switching frequency needs to be lowered to 540khz at 4.5v input. t on = dc/ frequency, or 1.35s. the f set pin voltage compliance is 1/3 of v in , and the i fset current equates to 38a with the internal 39.2k. the i fset current needs to be 24a for 540khz operation. as shown in figure 19, a resistor can be placed from v out to f set to lower the effective i fset current out of the f set pin to 24a. the f set pin is 4.5v/3 =1.5v and v out = 3.3v, therefore 130k will source 14a into the f set node and lower the i fset current to 24a. this enables the 540khz operation and the 4.5v to 28v input operation for down converting to 3.3v output. the frequency will scale from 540khz to 1.1 mhz over this input range. this provides for an effective output current of 8a over the input range. applications information figure 18. 5v at 8a design without differential amplifier v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss pllin ltm4601hv r1 392k 1% r fset 100k r set 8.25k c3 100f 6.3v sanyo poscap 4601hv f18 v out 5v 8a track/ss control review temperature derating curve refer to table 2 c2 10f 35v improve efficiency for 12v input c1 10f 35v r4 100k r2 100k v in v out f set pgnd margin control sgnd 5% margin v in 10v to 28v dual cmssh-3c3 sot-323 + 22f 6.3v
ltm4601hv 22 4601hvfb figure 19. 3.3v at 10a design figure 20. typical 22v to 28v, 1.5v at 10a design, 500khz applications information v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss pllin ltm4601hv r1 392k r4 100k r2 100k r set 13.3k r fset 130k margin control c3 100f 6.3v sanyo poscap 22f 6.3v 4601hv f19 v out 3.3v 10a track/ss control c2 10f 25v 3 v in v out f set pgnd sgnd 5% margin v in 4.5v to 16v review temperature derating curve + pgood v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss pllin ltm4601hv r1 392k r4 100k r2 100k r set 40.2k r fset 175k c out1 100f 6.3v c5 0.01f c out2 470f 6.3v margin control 4601hv f20 v out 1.5v 10a clock sync c3 100pf refer to table 2 for different output voltage c in bulk opt c in 10f 35v 3 cer v in v out f set v in pgnd sgnd 5% margin v in 22v to 28v review temperature derating curve + + pgood on/off
ltm4601hv 23 4601hvfb figure 21. 2-phase parallel, 3.3v at 20a design applications information v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss pllin ltm4601hv r1 392k 392k r4 100k r2 100k v out r set 6.65k c3 22f 6.3v c4 470f 6.3v v out 3.3v 20a clock sync 0 phase clock sync 180 phase c6 220pf margin control track/ss control track/ss control refer to table 2 refer to table 2 c5* 100f 35v c1 0.1f c2 10f 35v 2 v in f set pgnd sgnd v out v fb marg0 marg1 v out_lcl diffv out v osns + v osns ? pgood mpgm run comp intv cc drv cc track/ss pllin ltm4601hv v in f set pgnd sgnd 5% margin ltc6908-1 v in 6v to 28v pgood 2-phase oscillator 100pf c3 22f 6.3v 4601hv f21 c7 0.033f c8 10f 35v 2 *c5 optional to reduce any lc ringing. not needed for low inductance plane connection + c4 470f 6.3v + + v + gnd set 6 5 4 1 2 3 out1 out2 mod v out = 0.6v r set 60.4k n + r set n = number of phases 118k 1%
ltm4601hv 24 4601hvfb figure 22. dual outputs (3.3v and 2.5v) with coincident tracking figure 23. dual outputs (1.8v and 1.5v) with coincident tracking typical applications v out v fb v out_lcl diffv out v osns + v osns ? marg0 marg1 pgood run comp intv cc drv cc mpgm f set track/ss pllin ltm4601hv v in 3.3v 3.3v 3.3v track ltc6908-1 2-phase oscillator pgnd sgnd v + gnd set out1 out2 mod r4 100k 180 phase 0 phase margin control margin control 4601hv f22 r2 392k c3 0.15f c8 0.1f c2 100f 6.3v c1 10f 35v v in 6v to 28v r1 13.3k v out1 3.3v 10a r3 100k r1 118k c4 150f 6.3v v out v fb v out_lcl diffv out v osns + v osns ? marg0 marg1 pgood run comp intv cc drv cc mpgm f set track/ss pllin ltm4601hv v in pgnd sgnd r8 100k r6 392k r15 19.1k r16 60.4k c6 100f 6.3v c5 10f 35v r5 19.1k v out2 2.5v 10a r7 100k c7 150f 6.3v v out v fb v out_lcl diffv out v osns + v osns ? marg0 marg1 pgood run comp intv cc drv cc mpgm f set track/ss pllin ltm4601hv v in 3.3v 3.3v 3.3v track ltc6908-1 2-phase oscillator pgnd sgnd v + gnd set out1 out2 mod r4 100k 180 phase 0 phase margin control margin control 4601hv f23 r2 392k c3 0.15f c8 0.1f c2 100f 6.3v c1 10f 35v v in 6v to 28v r1 30.1k c8 47pf v out1 1.8v 10a r3 100k r1 182k c4 220f 6.3v v out v fb v out_lcl diffv out v osns + v osns ? marg0 marg1 pgood run comp intv cc drv cc mpgm f set track/ss pllin ltm4601hv v in pgnd sgnd r8 100k r6 392k r15 40.2k r16 60.4k c6 100f 6.3v c9 47pf c5 10f 35v r5 40.2k v out2 1.5v 10a r7 100k c7 220f 6.3v
ltm4601hv 25 4601hvfb package description please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. notes: 1. dimensioning and tolerancing per asme y14.5m-1994 2. all dimensions are in millimeters ball designation per jesd ms-028 and jep95 5. primary datum -z- is seating plane 6. solder ball composition is 96.5% sn/3.0% ag/0.5% cu 4 3 details of pin #1 identifier are optional, but must be located within the zone indicated. the pin #1 identifier may be either a mold or marked feature package top view 4 pin ?a1? corner x y aaa z aaa z package bottom view pin 1 3 see notes suggested pcb layout top view bga 118 0112 rev a ltmxxxxxx module tray pin 1 bevel package in tray loading orientation component pin ?a1? detail a 0.0000 0.0000 detail a ?b (118 places) detail b substrate 0.27 ? 0.37 2.45 ? 2.55 // bbb z d a a1 b1 ccc z detail b package side view mold cap z m x yzddd m zeee 0.630 0.025 ? 118x symbol a a1 a2 b b1 d e e f g aaa bbb ccc ddd eee min 3.22 0.50 2.72 0.60 0.60 nom 3.42 0.60 2.82 0.75 0.63 15.0 15.0 1.27 13.97 13.97 max 3.62 0.70 2.92 0.90 0.66 0.15 0.10 0.20 0.30 0.15 notes dimensions total number of balls: 118 e b e e b a2 f g bga package 118-lead (15mm 15mm 3.42mm) (reference ltc dwg # 05-08-1903 rev a) 0.6350 0.6350 1.9050 1.9050 3.1750 3.1750 4.4450 4.4450 5.7150 5.7150 6.9850 6.9850 6.9850 5.7150 5.7150 4.4450 4.4450 3.1750 3.1750 1.9050 1.9050 0.6350 0.6350 6.9850 fgh m l jk e abcd 2 1 4 3 5 6 7 12 8 9 10 11
ltm4601hv 26 4601hvfb package description please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. notes: 1. dimensioning and tolerancing per asme y14.5m-1994 2. all dimensions are in millimeters ball designation per jesd ms-028 and jep95 5. primary datum -z- is seating plane 4 3 details of pin #1 identifier are optional, but must be located within the zone indicated. the pin #1 identifier may be either a mold or marked feature package top view 4 pin ?a1? corner x y aaa z aaa z package bottom view c(0.30) pad 1 3 see notes suggested pcb layout top view lga 118 1011 rev a ltmxxxxxx module tray pin 1 bevel package in tray loading orientation component pin ?a1? detail a 0.0000 0.0000 d 0.630 0.025 ? 118x e b e e b f g 0.6350 0.6350 1.9050 1.9050 3.1750 3.1750 4.4450 4.4450 5.7150 5.7150 6.9850 6.9850 6.9850 5.7150 5.7150 4.4450 4.4450 3.1750 3.1750 1.9050 1.9050 0.6350 0.6350 6.9850 fgh m l jk e abcd 2 1 4 3 5 6 7 12 8 9 10 11 detail a 0.630 0.025 sq. 118x lga package 118-lead (15mm 15mm 2.82mm) (reference ltc dwg # 05-08-1801 rev a) detail b package side view bbb z s yxeee symbol a b d e e f g h1 h2 aaa bbb eee min 2.72 0.60 0.27 2.45 nom 2.82 0.63 15.00 15.00 1.27 13.97 13.97 0.32 2.50 max 2.92 0.66 0.37 2.55 0.15 0.10 0.05 notes dimensions total number of lga pads: 118 detail b substrate mold cap z h2 h1 a
ltm4601hv 27 4601hvfb package description pin id function pin id function pin id function pin id function pin id function pin id function a1 v in b1 v in c1 v in d1 pgnd e1 pgnd f1 pgnd a2 v in b2 v in c2 v in d2 pgnd e2 pgnd f2 pgnd a3 v in b3 v in c3 v in d3 pgnd e3 pgnd f3 pgnd a4 v in b4 v in c4 v in d4 pgnd e4 pgnd f4 pgnd a5 v in b5 v in c5 v in d5 pgnd e5 pgnd f5 pgnd a6 v in b6 v in c6 v in d6 pgnd e6 pgnd f6 pgnd a7 intv cc b7 C c7 C d7 C e7 pgnd f7 pgnd a8 pllin b8 C c8 C d8 C e8 C f8 pgnd a9 track/ss b9 C c9 C d9 C e9 C f9 pgnd a10 run b10 C c10 C d10 C e10 C f10 C a11 comp b11 C c11 C d11 C e11 C f11 C a12 mpgm b12 f set c12 marg0 d12 marg1 e12 drv cc f12 v fb pin id function pin id function pin id function pin id function pin id function pin id function g1 pgnd h1 pgnd j1 v out k1 v out l1 v out m1 v out g2 pgnd h2 pgnd j2 v out k2 v out l2 v out m2 v out g3 pgnd h3 pgnd j3 v out k3 v out l3 v out m3 v out g4 pgnd h4 pgnd j4 v out k4 v out l4 v out m4 v out g5 pgnd h5 pgnd j5 v out k5 v out l5 v out m5 v out g6 pgnd h6 pgnd j6 v out k6 v out l6 v out m6 v out g7 pgnd h7 pgnd j7 v out k7 v out l7 v out m7 v out g8 pgnd h8 pgnd j8 v out k8 v out l8 v out m8 v out g9 pgnd h9 pgnd j9 v out k9 v out l9 v out m9 v out g10 C h10 C j10 v out k10 v out l10 v out m10 v out g11 C h11 C j11 C k11 v out l11 v out m11 v out g12 pgood h12 sgnd j12 v osns + k12 diffv out l12 v out_lcl m12 v osns C table 5. pin assignment (arranged by pin number)
ltm4601hv 28 4601hvfb pin name a1 a2 a3 a4 a5 a6 v in v in v in v in v in v in b1 b2 b3 b4 b5 b6 v in v in v in v in v in v in c1 c2 c3 c4 c5 c6 v in v in v in v in v in v in table 6. pin assignment (arranged by pin function) pin name d1 d2 d3 d4 d5 d6 pgnd pgnd pgnd pgnd pgnd pgnd e1 e2 e3 e4 e5 e6 e7 pgnd pgnd pgnd pgnd pgnd pgnd pgnd f1 f2 f3 f4 f5 f6 f7 f8 f9 pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd g1 g2 g3 g4 g5 g6 g7 g8 g9 pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd h1 h2 h3 h4 h5 h6 h7 h8 h9 pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd pgnd pin name j1 j2 j3 j4 j5 j6 j7 j8 j9 j10 v out v out v out v out v out v out v out v out v out v out k1 k2 k3 k4 k5 k6 k7 k8 k9 k10 k11 v out v out v out v out v out v out v out v out v out v out v out l1 l2 l3 l4 l5 l6 l7 l8 l9 l10 l11 v out v out v out v out v out v out v out v out v out v out v out m1 m2 m3 m4 m5 m6 m7 m8 m9 m10 m11 v out v out v out v out v out v out v out v out v out v out v out pin name a7 a8 a9 a10 a11 a12 intv cc pllin track/ss run comp mpgm b12 f set c12 marg0 d12 marg1 e12 drv cc f12 v fb g12 pgood h12 sgnd j12 v osns + k12 diffv out l12 v out_lcl m12 v osns C pin name b7 b8 b9 b10 b11 - - - - - c7 c8 c9 c10 c11 - - - - - d7 d8 d9 d10 d11 - - - - - e8 e9 e10 e11 - - - - f10 f11 - - g10 g11 - - h10 h11 - - j11 - package description
ltm4601hv 29 4601hvfb information furnished by linear technology corporation is believed to be accurate and reliable. however, no responsibility is assumed for its use. linear technology corporation makes no representa - tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. revision history rev date description page number b 03/12 revised entire data sheet to include the bga package. 1C30 (revision history begins at rev b)
ltm4601hv 30 4601hvfb ? linear technology corporation 2007 lt 0 312 rev b ? printed in usa linear technology corporation 1630 mccarthy blvd., milpitas, ca 95035-7417 (408) 432-1900 l fax : (408) 434-0507 l www.linear.com package photos this product contains technology licensed from silicon semiconductor corporation. ? related parts 15mm 15mm 2.82mm 15mm 15mm 3.42mm part number description comments ltm4628 26v, dual 8a, dc/dc step-down module regulator 4.5v v in 26.5v, 0.6v v out 5v, remote sense amplifier, internal temperature sensing output, 15mm 15mm 4.32mm lga ltm4627 20v, 15a dc/dc step-down module regulator 4.5v v in 20v, 0.6v v out 5v, pll input, v out tracking, remote sense amplifier, 15mm 15mm 4.32mm lga ltm4611 1.5v in(min) , 15a dc/dc step-down module regulator 1.5v v in 5.5v, 0.8v v out 5v, pll input, remote sense amplifier, v out tracking, 15mm 15mm 4.32mm lga LTM4613 8a en55022 class b dc/dc step-down module regulator 5v v in 36v, 3.3v v out 15v, pll input, v out tracking and margining, 15mm 15mm 4.32mm lga ltm4601ahv 28v, 12a dc/dc step-down module regulator 4.5v v in 28v, 0.6v v out 5v, pll input, remote sense amplifier, v out tracking and margining, 15mm 15mm 2.82mm lga or 15mm 15mm 3.42mm bga ltm4601a 20v, 12a dc/dc step-down module regulator 4.5v v in 20v, 0.6v v out 5v, pll input, remote sense amplifier, v out tracking and margining, 15mm 15mm 2.82mm lga or 15mm 15mm 3.42mm bga ltm8027 60v, 4a dc/dc step-down module regulator 4.5v v in 60v, 2.5v v out 24v, clk input, 15mm 15mm 4.32mm lga ltm8032 36v, 2a en55022 class b dc/dc step-down module regulator 3.6v v in 36v, 0.8v v out 10v, synchronizable, 9mm 15mm 2.82mm lga or 9mm 15mm 3.42mm bga ltm8061 32v, 2a step-down module battery charger with programmable input current limit compatible with single cell or dual cell li-ion or li-poly battery stacks (4.1v, 4.2v, 8.2v, or 8.4v), 4.95v v in 32v, c/10 or adjustable timer charge termination, ntc resistor monitor input, 9mm 15mm 4.32mm lga

▲Up To Search▲

Price & Availability of LTM4613

	To Download LTM4613 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .